INO DATA FORMAT                                                 DATE::29-07-2010.
Event data: (16bit word)    size = 167 words

01.      0xAAAA
02.      0x5555
03.     Year   /* New  Addition  */
04.     Run number
05.     32 bit Event counter
        Event number_1 Lower word
        Event number_2 Higher word
                PC time RTCtime     ( All digits are in BCD format )
07.     RT_1    [ N.A ]                 [ microsecs - 3,2,1]
08.     RT_2    [ 0.1secs]              [ millisecs - 3,2,1]
09.     RT_3    [M2M1,S2S1]             [ M2M1,S2S1]
10.     RT_4    [D2D1,H2H1]             [ D2D1,H2H1]
11.     RT_5    [Y2Y1,m2m1]             [ N.A,D4D3]
12.     Data size [137 words from here]

13.     2 words Hardware 24 bit Master trigger Scaler counter
15.     2 words Hardware 24 bit Scaler for Scitilators Trigger (Trigger bit mark)
17.     Reserved  6 words { 24 bit Scaler or any use full info }
29.     29 to 44 TDC-1 to TDC-14 , Cal1, Cal2 (X-plane)
        45 to 60 TDC-1 to TDC-14 , Cal1, Cal2 (Y-plane)
61.     61 to 102:Latched bit information from 14 front end boards of X plane
                 {                  *Note 1           *Note 2         *Note 3
                   1'st Word:: |6 bits Board ID|6 Bits Mon Counter|1F|2F|3F|4F|    
                   2'nd Word:: |         Strip 32 to 17 RPC Latch info        |    * see note 4
                   3'rd Word:: |         Strip 16 to  1 RPC Latch info        |    * see note 4
                 }
        103-108    + 6 words for 2 Dummy Layer

109.    109 to 150:Latched bit information from 14 front end boards of Y plane
                  {
                    Same as in X-Plane
                  }
        151-156     + 6 words for 2 Dummy Layer
157.    157 to 167 : 11 words of latch information from the final Trigger
                     module( BARC module format yet to finalize )

Note 1: The MSB of the 6 bit board address represent the X or Y plane
        MSB = 0 for X Plane
        MSB = 1 for Y plane
Note 2: The 6 bit mon counter represents the current strip under monitoring.
Note 3: Bit=1 -> presence of 1F, 2F, 3F, or 4F signal respectively. (Due to timing issues, these fields do not hold reliable data.
Note 4: Bit=1 -> presence of signal on the RPC strip.


Monitor data: ( 16 bit word )   Size : 62 words
1.0x 5555
2.0x AAAA
3.Run number
4.Year  /* New Addition */
5.Monitor Record number
        PC time RTCtime     ( All digits are in BCD format )
06.       RT_1   [ N.A ]        [ microsecs - 3,2,1]
07.       RT_2   [ N.As]        [ millisecs - 3,2,1]
08.       RT_3  [M2M1,S2S1]      [ M2M1,S2S1]
09.       RT_4  [D2D1,H2H1]      [ D2D1,H2H1]
10.       RT_5  [Y2Y1,m2m1]      [  N.A,D4D3]
11. Monitoring duration in 10'th of Secs.
12. data size
13 IMT Mask Reg
14-15 Lto Rate
16-22 Individula layer  mask Reg
23->30 BARC Scaler Data F1X to F4X & F1Y to F4Y
   X-Layer Scaler
31.Higher Byte::  Board ID  = 0 to 15, MSB set 1 if Y plane else X plane.
   Lower Byte ::  Channel code = 0 to 39
32.Monitor scaler data
33 to 62  SrNo 32 & 33 repeats 15 times
   Y-Layer Scaler
63.Higher Byte::  Board ID  = 0 to 15, MSB set 1 if Y plane else X plane.
   Lower Byte ::  Channel code = 0 to 39
64.Monitor scaler data
65 to 94  SrNo 63 & 64 repeats 15 times